How to Check the Build Quality of a Smart Lock Sample Before You Approve It
A smart lock sample arrives. It powers up, accepts a fingerprint and looks as good as the photos. Function tests and finish approval usually get most of the attention, and the construction gets a glance.
Yet the sample is your first close look at how the supplier cuts, forms, joins, fastens and assembles the lock. A build review before approval catches problems a function test can't show, and it gives you reference points for checking production later.
Whether a sample comes from SivoLock or another manufacturer, a working keypad is only the start. The approval record should also cover the housing, fasteners, assembly and installation fit, so later production can be checked against something more useful than a successful demonstration.

Set Up the Review
Ask for two units if you plan to open one. Keep one intact for comparison and approval. For the other, agree with the supplier how it will be opened and reassembled, and whether it must be returned.
Have the reference ready: the drawings, specification or reference photos the sample is meant to match. Several checks below compare against them.
Have the tools ready: calipers, a straightedge, a flashlight, a magnifier, a soft white cloth and the screwdriver bits the lock needs.
Photograph both units as received: front, rear, edges, labels and packaging. Findings are hard to discuss later without a "before" picture.
Use one light source and one viewing position for every surface, and note them. Marks appear and disappear as the angle of light changes.
Record the model, version and finish, so each finding attaches to the right configuration.
The Outside: Faces, Edges and Joins
Flat faces. Lay a straightedge across a panel that is designed to be flat and look for light underneath. On brushed and polished panels, a long reflection, such as a ceiling light, shows waviness the eye misses head-on. Where parts are welded, heat can distort the metal; ASSDA lists distortion among the common stainless fabrication traps. Record any waviness and ask what causes it.
Cut edges and openings. Wipe a soft cloth along the outer edges, the reader window, the keyhole and the screw holes. A burr catches the fibers. Burrs cut installers' hands, scratch doors and hold dirt.
Joins between parts. Check alignment, gaps and flushness where the handle meets the panel and around the battery cover, the reader and the display. Compare them with the drawings or reference sample: not every surface is meant to be flush, and not every gap is meant to match its opposite side. Record each unexplained difference, and ask whether it comes from a one-off assembly issue, the design or the manufacturing process.
Windows and bonded parts. Look along the edges of reader windows, displays and glass panels with the flashlight. Record adhesive squeezed onto visible surfaces, gaps in the bond line, and any window that sits differently from the drawing. Ask the supplier whether the bond line is meant to be continuous and how the adhesive is applied.
Marks that matter beyond looks. Not every mark is cosmetic. ASSDA notes that scratches and gouges form crevices where contaminants collect, and that hardened adhesive residue from tape or protective film becomes a site for crevice corrosion. On stainless parts, small orange specks are a warning sign too: ASSDA calls embedded iron, from tools, grinding dust or wire brushes used on carbon steel, "the most frequently encountered fabrication problem", and those particles rust quickly. Record where each mark is and ask the supplier where it came from.
The Feel: Operate It Before You Judge It
Mount the lock on a door or fixture for a short session of use. This is a check of mechanical feel, not a trial installation.
Handle: check for wobble at rest, a smooth turn without grinding, and a full return every time. On double-sided locks, compare the two handles.
Fixing to the door: close the door firmly a few times. The panels should stay tight, without rattling or shifting.
Covers and buttons: battery and key covers should open and close the way the instructions describe, with any tool they need clearly identified, and stay closed. Keys and buttons should feel the same across the keypad.
Sound: shake the lock gently in your hand. Note any rattle and ask the supplier what is moving. Some movement can be part of the mechanism; a loose screw is not.
The Inside: Open One Unit
Opening the agreed unit reveals construction details you cannot see from the outside. Record them as reference points for later production checks. Photograph each layer before moving anything, and note anything that shifts or breaks as you open it, so defects present on arrival stay separate from changes caused by disassembly. Once opened, the unit no longer shows how well the original assembly sealed, so keep it out of any later water testing.
Inside surfaces. Leftover polishing compound, cutting oil or metal dust inside the housing shows how well parts are cleaned before assembly. On stainless parts this matters: ASSDA notes that oil and grease marks can provide crevices for localized corrosion. Keep residue separate from lubricant applied on purpose to moving parts, which many mechanisms need. Ask the supplier to identify any material you don't recognize.
Welds and heat tint. Where the housing has welded brackets, studs or seams, look at the metal beside each weld. On stainless steel, straw, brown or blue coloring is heat tint. ASSDA explains that welding can leave a colored oxide layer over a layer of steel depleted of chromium, which lowers corrosion resistance, and that the damaged layer should be removed by mechanical, chemical or electrochemical means. Inside a lock that stays dry, heat tint matters less; on an outdoor lock, moisture can reach inside surfaces too. ASSDA also lists weld spatter and undercut as crevice sites. Ask the supplier how weld areas are cleaned.
Material thickness and stiffness. Measure the housing with calipers at a few accessible points, and compare each reading with the specification for that point. Folded edges, overlapping layers and coatings are not single-wall thickness, so note what each reading includes. Then press each panel lightly by hand. Note any visible flex and ask whether it is expected for that design; treat it as an observation, not a strength test.
Fasteners. Check that every screw is present, fully seated and undamaged. Where thread engagement can be seen, compare it with the specified fastener and assembly details. Then look for mixed metals. ASSDA explains that galvanic corrosion needs three things: a liquid wetting the joint, metal-to-metal contact and a large enough difference in electrical potential between the metals. The more active metal corrodes. When the joint is wet, a small exposed area of the more active metal coupled to a much larger wetted stainless surface can corrode quickly. Zinc-plated or galvanized steel screws in a stainless housing are that case: ASSDA notes the zinc goes first, then the steel beneath it. Stainless screws in aluminum parts are common, but the aluminum around them can still corrode. On an outdoor lock, ask what the screws are made of and how each joint is isolated or kept dry.
Cables and connectors. Cables should run clear of sharp edges, screw points and moving parts, held in place without being stretched. Look for pinch marks where the housing closes. Connectors should be fully seated and latched where they have latches.
Seals and gaskets. Seals should be continuous, seated in their grooves, untwisted and uncut, with an even impression where they were compressed. If your photos from the opening show a seal already out of its groove, ask about it: on an outdoor lock, that is a likely path for water.
Battery compartment and modules. Battery contacts should line up with the cells, with springs intact. Circuit boards, readers and motors should be held firmly by their fixings, with no part relying on its cable to stay in place.
Turn Findings Into an Approved Reference
Sort each finding by what it affects: safety and security, function or installation, durability, or appearance. Agree with the supplier which findings must be fixed before approval and which can be accepted. Then get written answers on the open points, such as how welds are cleaned or what the screws are made of.
When a revised sample arrives, check each fixed point again, and repeat the quick outside and feel checks to confirm nothing else changed along the way.
When you approve, include the internal photos in the approval record alongside the outside views, so later inspections can check the same details. For appearance, agree a limit where it matters: a photo or a physical sample of the largest acceptable mark is clearer than a word like "minor".
Production lots can then be checked against that reference. For how to plan those checks, from sampling to defect classes and reinspection, see SivoLock's smart lock pre-shipment inspection checklist.
References
Australian Stainless Steel Development Association (ASSDA): Stainless fabrication: common traps to avoid
ASSDA: Pickling and passivation
FAQS
How many smart lock samples should I request?
Two. Keep one intact for comparison and approval, and agree with the supplier how the other will be opened.
What should I check on the outside of a sample?
Flat faces, burrs on cut edges, gaps where parts join, bonded windows, and marks such as embedded iron or adhesive residue.
Why should I open a sample unit?
It shows cleanliness, welds and heat tint, material thickness, fastener metals, cable routing, seals and the battery compartment. You cannot see these from outside.
What goes into the approval record?
Outside and internal photos, findings sorted by safety, function, durability and appearance, written supplier answers, and a limit sample for the largest acceptable mark.


